Hobbyking Stinger 64 Mk2. 2200 Nano First Flight

...the big day!

Since the ultimate smash I'd reconstructed the Stinger with a new fuselage and new larger and higher-spec powerpack, all of which I was eager to try out so, with a break in the rather poor run of weather, I headed to the field.

As ever, not having flown the Stinger for a while made me nervous. Additionally, I wasn't sure what the effect would be of the substantially-larger 2200 battery compared to the 1800 I'd previously flown with.

Eager to get the Stinger into the air before the sun disappeared behind clouds, I gave it a quick check before getting it ready to launch. Running the motor up for launch, the reaction felt a little odd. Blipping the throttle again revealed the reason - it was blowing air out of the intakes. I'd wired the motor in reverse.

Dashing back to the car for my toolkit, quite a way as I was flying in the paddocks, I headed back to the plane to remove wings and swap the plugs. Eventually the Stinger was back together, now developing positive thrust, but the sun had unfortunately taken a break behind a small patch of clouds.

Despite the disappointment of losing the beautiful afternoon glow, I hot full throttle and threw the Stinger up. Despite high expectations, this continued the run of miserable launches I've had, the Stinger knife-edging a few metres up. Correcting this and easing off the elevator revealed the next crisis; I hadn't done a good check on the trims and the Stinger was nosediving alarmingly.

Bringing it round I heaved on the elevator; going vertically fifty metres up is a nice safe place to make control adjustments.

After that things got a lot better; the augmented stripes made visibility so much better I was immediately more confident, and soon I had the Stinger making nicely-controlled low passes at speed, howling past at full throttle...

GeeBee R3 750mm TRILOGY: PART 3: First Flight

...a few surprises

The GeeBee got its chance for a first flight on a beautiful, if somewhat breezy, afternoon with lovely clouds spread across a giant canvas of bright blue sky.

Playing it safe for the first take-off, I had the GeeBee on the dirt to give it a take-off smoother run. After a quick taxi-test, I headed it into the breeze and eased up the power.

It takes off pretty easily and without fuss, but the first surprise came when I eased off the elevator and found it nose-diving rapidly, so much so that I only just caught it in time. It was also turning right, so I had a tense minute or so as I steered it clear of trouble as I adjusted the trims.

After that things were a lot more enjoyable; it turns out that the GeeBee is very floaty, another surprise, and is fun and easy to fly. In fact its characteristics lead me to believe it has 3D capabilities, now I just need to develop mine!

It turns very quickly and easily and, with full power, is pretty brisk without being super-fast, so it didn't take long before I was flying it with some confidence.

Bringing it into land it floated in straight enough, rounding out well. I let it drop just a fraction, still a good landing, but this small jolt was enough to dislodge one side of the undercarriage and loosen the other mount.

However this is easily corrected with a little superglue, and I'm looking forward to exploring the GeeBee's abilities further...

GeeBee R3 750mm TRILOGY. PART 2: The Build

...so how does this work?

The GeeBee is a nice-quality kit, with solid EPO fuselage making it a smarter-looking proposition than a Rarebear, for example. While having a simple screw-together construction, it does however its construction poses a few questions.

How does the battery setup work, and where's the best spot for the receiver?

The first question is a puzzler, for me anyway having only had planes with unfettered access to the battery. Obviously, unless you're happy remove the wing every time you fly it, you need the ESC lead to remain in the battery hatch so it's accessible through the small hatch opening.

This I found achievable by mounting the ESC against the side of the fuselage, preventing the lead from falling back into the fuselage. This setup seems quite reliable, although packing the battery in and then feeding in the lead and connectors is still squeezy and awkward.

Regarding the receiver, in this case a twin-antenna Orange R615x, I mounted it in the central fuselage cavity which corresponds to a cavity in the wing moulding above. And, connecting all the servos from the back and the ESC from the front gives a very neat installation.

Next challenge is the bracing wire; five pairs of different length wires needing to be clipped into tiny hooks. Fifteen tediously fiddly minutes later I was finished.

The last trick was spinner and propellor. The latter simply gets tightened with a nut, with the spinner base in behind it. Then the spinner is installed; it comes with double-sided tape but, really, that's never going to hold. So I superglued it in place, with cardboard slipped in behind the base to keep it spaced off the cowling.

With everything in place the little GeeBee was looking good...

GeeBee R3 750mm TRILOGY. PART 1: Unofficial Unboxing

...a great-looking little plane

I’d had the GeeBee sitting in the corner for a while and finally got around to unboxing it.

It’s a nice quality kit, coming safely boxed and individually wrapped so that all parts were in perfect condition. The fuselage is even secured in place with velcro straps, a first for me.

The GeeBee comes in the classic Texaco livery which looks great and the decal application is nice. The fuselage is full EPO including the cowling which is nice, however there is a downside - the battery access is a small hatch on the underside.

The 5g servos, in wings and fuselage, are pre-installed along with the control horns. The high-standing tail wheel is also fitted, leaving only the tail planes to be screwed into place. The wing, with locating pins up front, is also screwed into place - a glue-free assembly.

The iconic GeeBee undercarriage comes pre-assembled, with integrated wire reinforcing which also serves as the mount slotting into the wing. Included is sprung bracing wires stabilising the undercarriage as well as bracing the wings to the fuselage, which should look great assembled.

The kit comes with two three-blade props and two spinners, the latter being the only disappointment - they're EPO, with the cone apparently needing to be stuck onto the base with double-sided tape! I'm not surprised to read that people have ditched these for real spinners. In fact, had I known, I’d have tried to get a replacement spinner when I ordered the kit…

Trainstar Tough Trainer EPO 1400. D4023 850kv Replacement Motor.

...fitting the Trainstar replacement motor

Having struggled to get a replacement prop adapter for the Trainstar, I finally decided to get a whole new motor, the D4023 850v from Hobbyking.

This seemed rather wasteful as I only really needed the adapter, but anyway. The D4023 comes with a steel prop adapter, hopefully more durable than the Volantex aluminium item but is otherwise pretty much a direct equivalent replacement.

The D4023 does actually have a different mounting pattern on the bell  mount, three holes instead of four, but fortunately the Volantex saddle mount has a multi-hole configuration which accepts the three-hole pitch with no rework required, which is great.

So the installation is a pretty simple switch-out; even the wire length is just right. The only extra work required is that the D4023 doesn’t come with any connectors, but a few minutes soldering got some 3.5mm bullet connectors fitted just fine…

Trainstar Tough Trainer 1400 EPO. D4023 Motor Test Flight.

...test flying the new motor

Fortune smiled this afternoon with the growing cloud cover holding up just enough for a scenically sunny afternoon for flying. Conditions were a little choppy but, given the lovely afternoon, we were going to give it a try anyway.

As well as being the test flight with its new motor, this was also the first time I’d flown the Trainstar for months after its collision with a light pole, so it was perhaps not surprising that it was out of trim.

As soon as it took off, it was evident that the Trainstar had become very floaty, in contrast to the nose-down attitude I’d been flying it previously. Nevertheless, it was still fun to have it back in the air.

After having a bit of fun floating it around, I brought it in to check trims, and then it was back in the air, flying a bit flatter than before. It was still not smooth flying though, with gusty conditions and wind shear above tree level turning the Trainstar into a kite of sorts.

The new motor performed very well, at least as powerful as the OE unit, and perhaps a little more. Considering its modest cost and ease of replacement, it’s a viable alternative to Volantex’s dodgy prop adapter…

Raptor Glider D-Box Pro 2000. 5 Star Morning

...gentle flying on a beautiful morning

Winter mornings are often dull and overcast, sometimes with drizzle, mist or rain. However, on occasion, they deliver outstanding sunrises and, on this occasion, a five-star morning with mist, pretty clouds, sun, blue skies and no wind.

I haven't been flying in the mornings lately as sunrise around the solstice comes too late. However, having missed my alarm on this particular morning, I assed the field with sky alight with the sun about to rise.

With the Raptor on board this was like receiving a written invitation, so I headed to the field. The cold winter morning air makes the Raptor extra floaty, so that with flaps down it approaches so slowly as to appear in slow motion.

And, with no turbulence, one is able to make low passes and low turns in absolute confidence, adding to the tranquil mood of the morning...

Dynam DC-3 Dakota 1470mm. Spectacular Sunny Afternoon

...a pleasant sunny afternoon

Monday morning was grey and miserable but, just to be sure, I packed the DC-3 and Radjet. This was just as well because, by lunch time, the weather had cleared to a beautifully sunny and mild afternoon and I would have been most upset to have been flightless.

Happily I headed to the field with the afternoon winter sun flooding the fields with warm afternoon light as it began to dip towards the western horizon.

The DC-3 is a docile creature suited to slow flypasts and modest aerobatics, so I spent an enjoyable quarter of an hour doing just that. I managed a really nice touch and go as well as a fast flypast.

Being quite slow I have been pondering a few possibilities to see if it can be made a little speedier, but we'll keep those musings for another day...

Stinger Ready to Go

...hopefully it will be good

The Stinger has been reconstructed with its new fuselage and replacement fan unit, fitted with a zen-first R615X receiver  and, just yesterday, received its new Nanotech 2200 4S 45-90 power pack.

Apart from it looking sharp and new with the replacement fuselage, and interest in how the new DSMX receiver will work, it's the performance impact that the big nanotech will make that I'm most intrigued in.



And it is big; in fact it's too wide to fit easily into the fuselage, bulging the foam past the matching form of the canopy. I'm hoping that in due course the foam will compress a little to reduce this distortion but there's no denying that there's a lot of battery there.

My experience with 4S nano's on my Rarebear indicate that they offer substantial performance improvements, although I'm not sure whether, in this case, the additional grunt will be offset by the increase in mass over the 1800 40C Zippy I used previously.

Anyhow, I'm very interested to try out the reborn Stinger. I had, in fact, been hoping to get it out this afternoon for a test run but the weather wasn't cooperating with overcast and windy weather. Lets hope there's a mild and sunny afternoon in the offing soon...