Showing posts with label fly. Show all posts
Showing posts with label fly. Show all posts

Monday, 9 February 2015

Flight of Fancy

...what gets your spirit soaring

People's reaction to the planes varies a lot; some people are mildly interested, some could be mildly annoyed at the disturbance of the peace, whilst others are obviously captivated by the magic of flight. You can never really be sure, so I tend to keep the planes quiet and flying away so as not to cause disruption.



This morning I met a couple who arrived with their dog for some early-morning exercise at the field; talking to them as I headed back to the car with Canadair in hand, they'd been captivated by the sight of the water bomber flying around the morning sky.

And, the other day, I spoke to an ex-pilot out walking his dog, who'd enjoyed the speed and grace of the little Fox glider as it enjoyed an evening flight against a dramatic backdrop of clouds...

Thursday, 30 October 2014

Flying the Canadair

...at last

All the planets, including Pluto, finally aligned to provide an opportunity to get the Canadair in the air. All flight modifications had been completed, with the water rudder deleted, differential thrust programmed and the wing-float angle modified. All this with a plane I'd got as an easy-flying companion to the touchy Trainstar floatplane!


It was a lovely spring afternoon with just a moderate south westerly breeze as I turned into the still-open gates to the lake. Unpacking the Canadair I wasted no time in getting it onto the water, first trying a few mock takeoff runs which showed that the wing-float modification was working a charm, allowing the Canadair to run up to planing speed without risk of submarining.


However, realising that I was on the wrong side of the lake for the breeze, I left the Canadair floating mid-stream and sprinted to the the other side of the lake at a moderate pace. Finding the Canadair still out of the weeds, I taxied it over and lined it up for takeoff.

The first attempt was both alarming and laughable. Running the Canadair up to speed with full elevator, as I do to prevent the Trainstar from nosing in, the plane lept almost vertically into the air, dropping a wing in the process. Over-correcting, it then lurched in the opposite direction before finally flopping down onto the lake, its airspeed exhausted.



Trying again with just a touch of elevator had the Canadair executing a perfect lift-off, blurring the line between floating and flying as it eased off the water. As with the Trainstar, finally getting the Canadair into the air was a major achievement, although actually flying it was a breeze. Unlike it's companion, the Canadair is light and highly powered, making it easy to fly. Its abundance of stabilisers, winglets and large control surfaces also makes it easy to control.

Landing it was also pretty easy, again being light it slows down very quickly and, being low to the water, is pretty stable. So, now that it's all set up, I'm now looking forward to some relaxed flying with the Canadair...

Saturday, 27 September 2014

Canadair on the Water

...just weeding out problems

Yesterday was the first opportunity to get the Canadair 415 onto the water but unfortunately things didn't go well, to the degree that the Canadair didn't even come close to getting into the air, which was rather unfortunate as it was a spectacular afternoon for flying.


The first issue was the rudder, which proved almost immediately to be bordering on useless. It appears the thin wire mechanism, incorporated into the tail assembly, is much too lightweight for the job, so the Canadair ended up drifting rather aimlessly around the lake and ending up having to power it through the water weeds as steering it back wasn't an option.


Fortunately, as we know, the Canadair has a surfeit of power which saved it from the indignity of being marooned on the water. This was all the more impressive when one saw the amount of marine foliage that the fixed rudder had gathered as the plane trawled through the weeds.

The second issue was that one wing was heavier than the other so that, despite the plane accelerating on the water, I was unable to get the wings levelled. As a corollary, with the float stuck on the water, the Canadair was progressing in slow circles.

I eventually gave up and ploughed it back to shore. The wing balance is a relatively easy fix, however the rudder function is a more taxing issue altogether, and something I'll have to do some research on...

Thursday, 18 September 2014

Performance Anxiety

...how big is your prop?

The only minor concern I have regarding the Canadair 415 is whether the props are sufficiently large; I traded in the 8x3.8 slow-fly props for three-bladed 7x4.5's following the methodology of dropping one size going from two blades to three. However, in this case, the original prop is a slow-fly paddle version, so I'm thinking that going for a regular eight-inch three-blade would have been a better equivalency. 


Anyway, I might do a power test on a scale just to get a rough idea of how much thrust to expect; the 210W bell motors are rated at a max 880g thrust which, pushing the lightweight Canadair 415, would probably give it unlimited vertical performance...

Tuesday, 16 September 2014

Canadair 415 Ready to Roll

...at last

After a long and tedious episode of head-scratching and problem solving, the Canadair 415 is finally ready to fly, and it looks great!



Hanging in the study it exhibits the nose-down attitude with which I believe it flies, and the metallic spinners finish it off beautifully. Having read some discussions, I finished it off with a clear enamel spray as the foam is a little dry and I'm sure prone to staining, especially as the lake where I fly is actually a stormwater basin...

Friday, 12 September 2014

Searching for Slopes

...get the gliders soaring

I have lately been searching for places to get the gliders soaring instead of just cruising around; more what they're supposed to do. However, unfortunately, good soaring sites aren't to be found in suburbia so I've had to do a bit of searching.



I took the Phoenix for a fly to a great slope soaring site, unfortunately having literally zero wind meant it was just a regular flying session, although with a spectacular panoramic view. Hopefully I'll get to return when the breezes are favourable...

Friday, 29 August 2014

Trainstar Floatplane Sorted

...finally enjoying the moment


Yesterday afternoon I headed off to the lake again with the Trainstar, hoping that finally all the work I'd put into sorting it out would pay dividends and I'd be able to have an enjoyable afternoon punting it around the lake.

As it turned out the flights were really good; nice smooth takeoffs, peaceful and uneventful flights finished off with reasonably good landings. Using full elevator for landings this time, I managed to keep the Trainstar on its floats every time although it was still dropping too fast. The last tweak I need to do then, is to take off the flap mix I've been flying with.


This is good on the gliders when flying slowly however, with the Trainstar having to fly on about three-quarter throttle, the tail doesn't need any lifting. So, by switching the mixing off, it will give me a little extra elevator travel, just what I need to be able to level the Trainstar out on landing, hopefully enough to eliminate the bouncing which has been a characteristic of every landing it's made so far.

Changing the elevator setting will hopefully also give teh Trainstar teh ability to climb a bit better, as at the moment it flies pretty flat, which can be a slight concern given the number of trees lining the lake's edge.

The good landings were, of course, a great assistance ino keeping the servos dry...

Sunday, 24 August 2014

Waterproofing Servos

...silicone sealer and dielectric grease

Having thought the Trainstar floatplane was completely sorted, I've discovered that the wing servos, in particular the aileron servos with their exposed extension join, are prone to water ingress.

Due to the smallest waterproof servo available being much too large to fit into the wing, it was necessary to waterproof the existing servos and connectors. I had intended to use dielectric grease however I was concerned about contamination affecting the covering tape over the servo wires and so opted instead to just go with silicone sealer.



I sealed the cable entry to the servo housing, which seems like the most likely water entry point, and sealed the servo connector and the extension harness. The joins in the servo housing didn't seem like a problem, and I haven't sealed around the pinion gear due to access problems on the already-installed servos.

This is the one area that would require the grease, however I was wondering whether a haphazard application of grease might be worse than none at all, considering that the area most accessible would be on the underside, possibly trapping any splashed water. So I think I'll just try the Trainstar as is and see how it goes...

Friday, 22 August 2014

Floatplane Landings

...don't try too hard

Conditions today were idyllic, a beautiful warm afternoon with a light easterly blowing, and the lake deserted as usual except for a flock of moorhens and the odd duck.

With the Trainstar now fully sorted, I was looking forward to a leisurely afternoon flying the floatplane around and enjoying the gorgeous weather.

With the rudder servo keeping things straight on launch I could concentrate on managing the liftoffs; this takes a little doing as one needs to ease off the up-elevator required during the takeoff run, however the liftoff is quite sudden and tricky to anticipate. Anyhow, the launches were a little better but still need some work.



The landings, however, were atrocious, with the first attempt off an awkward approach being all over the place and ending with the Trainstar nosing into the lake. Fortunately it was close to the shore and the breeze assisted in bringing it back without the need to haul out the dinghy.

The flights were otherwise very pleasant, with the 2700mAh battery giving good power on launch and surprising endurance in flight. The controls are still a bit sensitive, and with the weight of the floats the Trainstar is quite sensitive, however I think I just need to dial up teh expo a bit to calm things down.

My last landing, by default, was off a nice long approach after my initial botched effort, and I greased the floats in on what I thought to be my best landing so far, when suddenly the float dug in and the Trainstar was suddenly nose-down in the lake, again.

I have made lots of bad landings, but never has the the Trainstar actually gone in. I think I was trying to get it too smooth and was lacking up-elevator to keep things on an even keel...

Wednesday, 20 August 2014

Float Rudder Servo

...more than a nice-to-have

Subsequent to the issues I'd experienced with the cable-operated water rudder on my Trainstar seaplane, I have retrofitted the float with a direct-acting rudder servo. I chose a 40g gram servo, rather oversized but the smallest waterproof servo that was available. I mounted this directly to the float in a cutout I made, the simplest and easiest method.


Today I had the first opportunity of trying this out at the resident lake, and the result was  nothing short of a remarkable improvement. The Trainstar, which previously zigzagged around the lake at will, now tracked remarkably straight and true, the oversized servo making sure that the rudder didn't deviate a millimetre, a far cry from the now-evident lack of control with the cable system rigged off the plane's rudder.


I had originally thought a servo-operated system would be preferable, but hadn't wanted to cut into the floats. Now, having experienced the amazing improvement in stability and likely improved reliability, I would suggest a float-mounted rudder servo to be an absolute necessity...

Friday, 15 August 2014

The Problem with Seaplanes

...try and try again

My efforts at converting to water planes has been rather fraught and, in many ways, echoes the tribulations I experienced when starting flying radio control.

Firstly trying to find suitable venues has been a challenge in itself; too many people, too close to houses, too far to walk from the car or locations only occasionally accessible. And, with the Trainstar needing a fair bit of headway to get airborne, the size of the lake needs to be quite generous.



The Trainstar seaplane is also not the easiest to take off or fly, in large due to the oversize floats making it marginally powered. Additionally, the Trainstar is skittish on launch which, when combined with its gravid nature as a seaplane, make getting it airborne a bit of a hit and miss affair.

Additionally, I've discovered that the cause of the Trainstar stalling and consequently nose-diving into the lake were due to the cable for water rudder sticking, providing no rudder input during left turns. I am in the process of resolving this by adding a waterproof servo directly onto the float, a much better system but which I hadn't adopted initially to avoid having to cut into the floats.

Incidentally, the ESC didn't survive it's inebriation, becoming smoking hot to the extent it unsoldered one of the motor leads. This did, however, provided an opportunity to utilise a spare 35A ESC I've had sitting on my spares shelf for ages...

Thursday, 7 August 2014

HMS Rescue

...first retrieval of the floatplane

Today the planets finally aligned, with it being calm, the rain remaining in abeyance and access to the lake being open. Things hadn't gone smoothly on the way, however, having to dodge a police roadblock and then having to hunt for the secret access point.

Finally, however, with all missions successfully completed, I arrived at the launching point ready for the Trainstar floaplane's second flight. There was just the slightest suggestion of a breeze, the lake calm and reflecting the tranquil palette of the surroundings.

The Trainstar was equipped with the new larger battery, which I hoped would provide the extra flying time to avoid awkward situations (plane marooned in the middle of the lake with a flat battery) and also provide a little extra grunt when necessary.


The takeoff runs I'm still finding problematic, with the Trainstar being quite skittish at speed and having a tendency to veer. Nevertheless I did manage a few launches and some pleasant flying across the lake.

The one issue I have encountered, twice in this session, is turning; sometimes the Trainstar will get into a tightening turn, whilst other times it won't turn tight enough. It was the latter cases which proved problematic, with the Trainstar ending up stalling and flopping nose-first into the lake.

In a testament to the unsinkability of the floats, both times the Trainstar settled back down onto the floats however, by the second occasion, the ESC had a little too much to drink and went for a lie-down. As a consequence I had to break out HMS Rescue for the first retrieval attempt.

Due to the inflatable being nicely packaged up I hadn't bothered doing a test run beforehand, however I found that, in conjunction with the electric pump, the boat was ready to go in a few minutes and, once I'd figured how to install the oars into the oarlocks, I was on my way out onto the lake.

The inflatable did surprisingly well, although my rowing skills left something to be desired. For the future I think I'll get some sort of tow rope for returning the plane, as trying to shepherd the untethered plane back to shore was rather taxing.

So all ended well, except to see whether the ESC can be resuscitated or needs replacing...

Wednesday, 6 August 2014

Super Scooper has Landed

...or at least arrived

A post office card left yesterday was exchanged for a large cardboard box which I loaded into the car and scooted for home. It was the Canadair 415 water bomber, a bit ahead of schedule having been ordered from the international warehouse which usually takes a little longer, so there must have been a tailwind.



I've yet to unbox it, having just extracated it from its plain cardboard armour, but a brief inspection of the extra goodies I'd ordered came with a sharp pang of disappointment, the ESC's come with no connectors. On either end. That means five wires having to be soldered by mister useless. For each ESC, this being a twin-engined plane.

Fortunately I have two spare XT60 plugs, however no bullet connectors for the motor. So that means a trip to one of the local hobby shop for some overpriced parts...

Dam Lakes

...somewhere for the Trainstar to call home

My efforts at getting the Trainstar floatplane in the air again have been unsuccessful, in part due to the weather, as in the case of today, in part due to misinformation, like yesterday, and partially because I want a completed deserted venue as I'm rather shy when I'm learning.


Yesterday I visit a great potential site, however it's bordered by houses but, mainly, had several fisherman whom I'm sure wouldn't be impressed with a buzzy floatplane invading their tranquility. However, on the way home I passed the lake where I'd first flown the Trainstar and was surprised to find the gates open, it being advertised as open only a few days a week.

I'm now hopeful that this is the case on most days, so will be taking the Trainstar along in the hope that I will be able to fly it more regularly and with less complication than thus far.

Sunday, 3 August 2014

HXT or XT60

...connector shmonnector

The new Zippy compact batteries for the Trainstar were a bit of a surprise, coming with a different connector to what I'm used to. The Turnigy 2700mAh, with a 20C rating, had XT60's whereas the 25C Zippy has HXT's . I guess, therefore, that this is the threshold for the higher-rated HXT connectors.

I've been trying to decide what to do, with my ESC having the XT60 connector, thinking that retaining the high-performance connectors would be preferable. However the mating connector has proved difficult to find and, as I recently realised, my charger doesn't have facility to connect to HXT leads.



So I might just change the connectors on the batteries to XT60's and be done with it. That way it'll suit the ESC and the charger, although necessitating changing two connectors, with soldering not being my nemesis...

Tuesday, 29 July 2014

In the Interim

while the weather is wild...

The extreme tranquility of last week has, unfortunately, been replaced by gusty winds forecast to last for the rest of the week. As such, I haven't ventured out to fly anything, least of all the floatplane.

The larger batteries for the latter are on there way, and I'm looking forward to familiarising myself with the Trainstar floatplane characteristics a bit better. The new batteries should provide significantly longer flight times, but I also think that a more considered flying regime will help keep the chubby floater in the air for longer as well.



Finally in the process of reconstruction, now that I've received the replacement ducted fan, adhesive accelerator and the urge to do it, the Stinger is resuming shape. The pace of the reconstruction is slow as I'm making sure that each rip and crack is properly bonded before proceeding to the next, but also the warnings on the accelerator pack have me evacuating the room after each burst of strawberry-scented aerosol.

The foam should go back into shape reasonably well, and I think I'll smooth out the joins with a bit of filler. The only question marks are against the motor and the servos as to whether those survived the massive impact unscathed. Anyhow, we'll know that when the body has been restored and I get the electrics connected up again...

Saturday, 26 July 2014

Canadair 415

...a friend for the Trainstar

Having finally been able to get the Trainstar floatplane launched and flying, even if somewhat crudely, I've been considering getting another water plane for a bit of variety when venturing out to the lakes or dams.

One plane that caught my eye was the Canadair 415 water bomber and, having read a few of the reviews, it comes well recommended and seems easy enough to launch and fly, unlike the Trainstar which is a bit more on the tricky side of things!

One thing I wasn't all that keen on is that the Canadair is only available in ARF form, requiring one to source components. Mainly this is fine, although the motor is my main concern, especially the mounting for both the motor itself and the prop. Anyway, I've followed the description and hope things will work out well, along with a couple of the 25A Plush ESC's which seem to be good.

I'll be running it off the 2200mAh's which I've been using on the Trainstar, and from what I've read that should be quite adequate. The Trainstar, on the other hand, will be upgraded to 2700mAh's to give extended flight time as a result of it's power-hungry nature from its oversized floats.

So, in a week or two we should have a bit more news of what it looks like and how the Canadair goes together...

Friday, 25 July 2014

Trainstar Floatplane Thoughts

...after the first flight

Finally getting the Trainstar floatplane into the air was quite something; I was uncertain whether the additional weight and drag would render the Trainstar waterbound and, if it did fly, how well or indeed, whether it would be manageable at all.

The first, very brief, flirtation with the sky did at at least confirm that it could fly, and that it actually even floated on the air quite well, giving me a little confidence so that, when I returned a few days later intent on getting it flying, that I could anticipate at least some success.

The Trainstar flew unexpectedly well, I suppose given that I hadn't expected that it would fly at all and, that it manages to maintain a turn at all, with the weight of the floats, is quite remarkable. However, in this case, I think the water rudder plays a part in keeping the floats up in the turn, meaning that you need to keep the rudder on or the self-centering effect very quickly brings things on an even keel.



The generous proportions of the floats makes the Trainstar virtually unsinkable, righting the plane even when it has tipped over with the prop flicking the water and when the wingtip has been on the water at speed during an attempted launch.

The flip-side, however, is that the Trainstar is very slow, and turning into the wind on approach turns moderate pace into pedestrian approach. I've only flown it with the flaps down, in addition to the slight down attitude I dialled into the ailerons, meaning the the Trainstar is flying in a very high-lift configuration. As such it becomes very floaty when the power is off.

I'm interested to fly it without flaps to see whether the reduced drag improves it's flight. Also, it seems the floats contribute to lift up front, which helps to keep the nose up. However I think the consequent drag also tips the nose down under power.

Lastly, another apparent effect of the additional mass and drag is that the flight times are reduced significantly. I'm looking at a slightly larger battery, which is also only slightly heavier, to improve this. However I think that with a better appreciation of how it flies, that I may be able to improve on this and reduce the amount of full throttle flight required...

Wednesday, 23 July 2014

Trainstar Floatplane First Flight

...it flies!!!

Opting to go with tenacity, due in part to today being the last very calm day forecast, this afternoon I headed off to the lake again with the Trainstar. The lake was not the location of first flight test, but rather another smaller venue promising virtually no onlookers, a feature which I found highly desirable.


There was a slight breeze blowing, not enough to unsettle the surface of the lake but sufficient to lend some assistance to the Trainstar to get airborne. The wind was also a northerly, helpful as access to the lake is at the southerly end.



The Trainstar was soon unpacked and on the lake, all tested and ready to go. I can't exactly remember the sequence of events, this first session also not being video'd for fear of tempting fate. Nevertheless, after a few false starts, I had the Trainstar in the air and flying.

Having had a brief airborne episode before I knew it would fly, although not exactly how, so the first takeoff was very much a beginner effort, with the Trainstar being hauled up, the climb angle eased off and then immediately increased as the plane started to drop, not being at all sure how it would behave.


The turns also took some getting used to, the weight of the floats dramatically increasing the self-righting effect the Trainstar has thanks to its wing dihedral. Nevertheless, the Trainstar still climbed and turned surprisingly well, and I cruised it overhead before turning back over the lake.

As I mentioned before, it becomes very floating with power off, I think due to the increased flap setting I'm using, although I'd expected the opposite with the float drag. However, having said that, I did expect the boat-shape of the floats to contribute some lift so perhaps that effect is more than anticipated.

At any rate the Trainstar floatplane is very predictable of landing approach once the speed has dropped off from cruise, although I still only managed one landing which was good, the others being a decaying series of slapping jumps off the lake. However, due in no small part to the generous nature of the floats, the plane never once ended in the drink, the buoyancy and stability of the floats righting and steadying the Trainstar every time, even once when I had the wingtip on the water with power still on full.

The only problem I had was running out of battery one one last approach, the Trainstar landing in the middle of the lake, having to resort to occasional brief bursts on reserve power and the breeze to return the plane to the shore...

Floatplanophobic

...need to gather the nerves

I returned today to the lake, ostensibly for the second attempt to take flight, but found myself so uncomfortably nervous that I ended up refraining from any attempt, despite the immaculately calm cool and sunny conditions.

I haven't abandoned hope of flying the floating Trainstar, rather that I didn't want to risk flying it when very much not in the zone. As I'm sure I've said before elsewhere, flying when you're not all there is an invitation for disaster, something I've proven repeatedly.

However, there is a fine balance between tenacity and dogged stupidity. The problem is you don't know where the line is until it's been crossed, with evidence posthumously clarifying with hindsight. However, there is a very familiar feel to this chapter, learning to fly all over again, very much like with the Floater Jet; I don't know why the takeoff run is all over the place, yet I don't want to give up. But I'm also wary of carrying on regardless and ending up with a capsized plane.



On the plus side, however, is the fact that the floats are oversized, have been positionally optimised and have proven to be a very stable setup. Also, the Trainstar has actually taken flight, and landed basically by itself, needing nothing more than a straight-ish run and a nudge on the elevator.

So, what's all the panic about? Well, I don't have the takeoff run under control, as I mentioned. And I wasn't even sure it'd fly, although that has been demonstrated, even if only briefly. And, if things really go pear-shaped, I have a rescue boat at hand, which would actually be fun to try out even if the motivation for the outing may be less so.

So, in reflection, all I need to do is put the Trainstar on the water and get it running reasonably straight.

Really not a huge drama...